Concrete Milling
At Surfprep we offer a full range of concrete milling services.
We have a large variety of well maintained bobcat milling heads that range in width from 75mm up to 600mm, with the ability to mill down to 50mm per pass and carry out work on all grades of concrete and epoxy surfaces. Our concrete milling heads can cut channels, bevel edges or even profile large areas. All our bobcats are road registered and arrive complete with hazard lights, flashing beacons, reversing beacons (white noise) and rear view mirrors.
Our operators are licensed to a minimum of class 2 with WTR endorsements and all hold current sitesafe passports and first aid certificates. 24/7 coverage available.
Click images to view slideshows of our concrete milling work »
Customer: Fulton Hogan
Job: NGA Newmarket, St Johns on-ramp southbound
Description: Surfprep’s Bobcat being lifted into place by a hiab.
Customer: Clearwater Construction Ltd
Job: Westfield Plaza, Manukau City
Description: Surfprep’s bobcat milling 40mpa cementitious levelling compound off at a depth of 20mm per pass and 250mm wide.
Customer: The Tile People Ltd
Job: Sylvia Park, Auckland
Description: Surfprep’s Dingo milling out a channel in the 30mpa concrete floor to make way for new aluminium expansion joints.
Customer: Fulton Hogan
Job: NGA Newmarket, St Johns on-ramp southbound
Description: Milling 10mpa slurry fill concrete at a depth of 50mm per pass and 600mm wide.
Customer: Fulton Hogan
Job: NGA Newmarket, St Johns on-ramp southbound
Description: Gap7 sized concrete millings left behind by machine.
Customer: Fulton Hogan
Job: NGA Newmarket, St Johns on-ramp southbound
Description: Total depth cut varied between 10mm and 120mm, this is varied by the operator while on the move.
Customer: Fulton Hogan
Job: NGA Newmarket, St Johns on-ramp southbound
Description: The milling head can also be adjusted to bevel edges or cut over an edge.
Customer: Clearwater Construction Ltd
Job: Westfield Plaza, Manukau City
Description: Gap7 sized milled material ready to be picked up. We use a 1800mm wide broom bucket for this.
Customer: Clearwater Construction Ltd
Job: Westfield Plaza, Manukau City
Description: Typical edge line and texture left by mill. Edges can be saw cut to tidy up and milled surface can be ground to reduce texture if required.
Customer: The Tile People Ltd
Job: Sylvia Park, Auckland
Description: Machinery is connected to vacuums or water jetting is used to suppress dust.
Customer: The Tile People Ltd
Job: Sylvia Park, Auckland
Description: The Dingo’s compact size means we call get in to confined spaces and still move around.
Customer: The Tile People Ltd
Job: Sylvia Park, Auckland
Description: Milled channel when complete, 200mm wide and 20mm deep.
Customer: Haydn & Rollett Ltd
Job: Inland railway port, Hamilton
Description: Surfprep’s bobcat milling to level a concrete slab prior to the construction of a water tank plinth.
Customer: Westfield NZ Ltd
Job: Downtown Plaza, Auckland City
Description: 60mm has been milled off of the existing concrete slab to make way for the insertion of new 40mm pavers.
Customer: Tyres 4 U Ltd
Job: Tyres 4 U driveway - Avondale
Description: This speed hump needed to be reduced in height by 40mm to allow limousines to drive across it without getting stuck.
Customer: Westfield NZ Ltd
Job: Downtown Plaza, Auckland City
Description: 60mm has been milled off of the existing concrete slab to make way for the insertion of new 40mm pavers.
Customer: Tyres 4 U Ltd
Job: Tyres 4 U driveway - Avondale
Description: Surfprep’s bobcat and concrete mill, milling 40mm per pass off the speed hump at a width of 250mm.
Customer: Tyres 4 U Ltd
Job: Tyres 4 U driveway - Avondale
Description: The speed hump was constructed from McCullums Chip and still no match for Surfprep’s concrete mill.
